Choose your language

Choose your login

Support

Just-in-time new user creation (JIT provisioning)

This page applies to:

Last updated November 17, 2026

Some organizations want all of their users pre-loaded in PaperCut Hive or Pocket so they’re all set up and ready to go. But some organizations prefer to create users in PaperCut Hive or Pocket the first time they interact with the printing system — commonly known as just-in-time provisioning (JIT). Yet other organizations prefer a blended approach: some users pre-loaded, and others allowed to create themselves.

The good news? PaperCut Hive and Pocket support all these options for organizations syncing users via User and group sync.

What is Just-in-time new user creation?

Just-in-time new user creation — known in PaperCut NG/MF as On-demand user creation — dynamically provisions new users in PaperCut Hive or Pocket when the user interacts with the system for the first time.

Who should use Just-in-time new user creation?

Organizations using User and group sync should consider using Just-in-time new user creation. It avoids needing all users to already exist in the Users list before they can start printing, which is especially useful when a user is added to your organization between syncs from your identity provider, or if you’ve set up a sync configuration without automatic syncing. From the user’s perspective, they can just log in — no need to call up the IT desk to ask for an account, and no need to wait until the sync next runs.

Just-in-time new user creation vs Team Signup

Not sure whether to use JIT provisioning or Team Signup? Most larger organizations with syncing from an identity provider will prefer JIT provisioning. However, Team Signup is handy for guests and smaller organizations. It’s possible to use both features together.

Team Signup

Just-in-time new user creation

Requires identity provider connected to PaperCut Hive or Pocket

No

Yes

Checks against a pre-existing user list

No

Yes

Uses email domain to approve user creation

Yes (if domain-based auto-approval configured)

Yes, if user included in sync configuration User Source

Inherits attributes and groups from identity provider

No — unless also included in a sync source (attributes and groups will be synced/imported on the next sync run)

Yes

Inherits policies on user creation

Yes

Yes

Inherits group policies on user creation

No

Yes

Access request sent to organization admin to approve

Yes (unless domain-based auto-approval is set up)

No

Initial user interaction with the system

MFD touchscreen access request or scanning QR code on site

Log in on computer (client authentication, task tray log in, User Portal log in)

How does Just-in-time new user creation work in PaperCut Hive or Pocket?

In PaperCut Hive and Pocket, JIT provisioning is a setting within a sync configuration in User and group sync. (JIT provisioning is not available through user sync Add-ons.) It can be set on a per-sync configuration basis, allowing a more fine-grained approach to provisioning users.

As part of setting up a sync configuration in User and group sync, you need to define:

  • a User Source (the users/groups who are imported into PaperCut Hive or Pocket during a sync)
  • User Attributes (the data imported along with a user to populate the user’s profile)
  • whether or not an invitation email will be sent to new users created during a sync.

These definitions are also used during JIT provisioning.

If JIT provisioning is enabled, this is the process PaperCut Hive or Pocket follows to provision the user:

  1. A future user (who does not yet exist in the Users list) interacts with an authentication event in PaperCut Hive or Pocket, in one of the following ways:
    • The user prints for the first time with a bulk-deployed, unlinked client (the authenticate-on-print workflow). Note: The task tray must include the organization ID during bulk deployment setup.

    • The user attempts to log in to the PaperCut Hive or Pocket User Portal from the organization-specific login URL. (Note: JIT provisioning is not triggered from the papercut.com login page. It is only triggered from the organization-specific URL).

    • The user logs in via the task tray. Note: The task tray must include the organization ID during bulk deployment setup.

  2. A login page is displayed to the user.
  3. The user logs in using an enabled authentication method. (Note: if logging in via Email and Password, the user must first create an Email and Password account, and provide their email, password, and username.)
  4. PaperCut Hive or Pocket checks if the user already exists in the organization’s Users list:
    • If the user exists, they log in, and no JIT provisioning is required.

    • If the user doesn’t already exist, PaperCut Hive or Pocket checks to see if it is allowed to create the user via JIT provisioning:

      1. First, it confirms that JIT provisioning is enabled in at least one sync configuration in User and group sync.
      2. Then it checks to see if the user is included in the sync configuration’s User Source.
      3. If the user is included in a User Source, it creates the user and adds them to the Users list.
    • PaperCut Hive or Pocket imports the user’s attributes and uses them to populate the user’s details in the Users list, and also applies memberships and policies to the user.

  5. The user logs in.

How to set up JIT provisioning in PaperCut Hive or Pocket

JIT provisioning is a setting in User and group sync. Learn how to:

Comments

Comments are not available in this preview environment. On papercut.com, this space shows the live Disqus comment thread for this page.